49 CFR Part 192

§ 192.632

Engineering Critical Assessment for Maximum Allowable Operating Pressure Reconfirmation: Onshore steel transmission pipelines.

Subpart L — Operations

49 CFR Part 192 § 192.632 is in the full corpus.

Engineering Critical Assessment for Maximum Allowable Operating Pressure Reconfirmation: Onshore steel transmission pipelines.

Start your 7-day trial to open it in the cross-referenced reader.

Start your 7-day trial Log in

49 CFR Part 192

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

Verify on eCFR ↗

A preview of 49 CFR Part 192 — its structure, and a few AI-generated plain-English summaries. The full cross-referenced text is available to subscribers.

What's inside

Subpart AGeneral
Subpart BMaterials
Subpart CPipe Design
Subpart DDesign of Pipeline Components
Subpart EWelding of Steel in Pipelines
Subpart FJoining of Materials Other Than by Welding
Subpart GGeneral Construction Requirements for Transmission Lines and Mains
Subpart HCustomer Meters, Service Regulators, and Service Lines
Subpart IRequirements for Corrosion Control
Subpart JTest Requirements
Subpart KUprating
Subpart LOperations
Subpart MMaintenance
Subpart NQualification of Pipeline Personnel
Subpart OGas Transmission Pipeline Integrity Management
Subpart PGas Distribution Pipeline Integrity Management (IM)
Appendix A to Part 192[Reserved]
Appendix B to Part 192Qualification of Pipe and Components
Appendix B to Part 192 I
Appendix B to Part 192 I.A
Appendix B to Part 192 I.B
Appendix B to Part 192 II
Appendix B to Part 192 II.ABending Properties
Appendix B to Part 192 II.BWeldability
Appendix B to Part 192 II.CInspection
Appendix B to Part 192 II.DTensile Properties
Appendix B to Part 192 III
Appendix B to Part 192 III.AInspection
Appendix B to Part 192 III.BSimilarity of specification requirements
Appendix B to Part 192 III.B.1
Appendix B to Part 192 III.B.2
Appendix B to Part 192 III.CInspection or test of welded pipe
Appendix B to Part 192 III.C.1
Appendix B to Part 192 III.C.2
Appendix C to Part 192Qualification of Welders for Low Stress Level Pipe
Appendix C to Part 192 IBasic test
Appendix C to Part 192 II
Appendix C to Part 192 III
Appendix C to Part 192 III.1
Appendix C to Part 192 III.2
Appendix D to Part 192Criteria for Cathodic Protection and Determination of Measurements
Appendix E to Part 192Guidance on Determining High Consequence Areas and on Carrying out Requirements in the Integrity Management Rule
Appendix E to Part 192 I
Appendix E to Part 192 II
Appendix E to Part 192 II.a
Appendix E to Part 192 II.b
Appendix E to Part 192 II.c
Appendix F to Part 192Criteria for Conducting Integrity Assessments Using Guided Wave Ultrasonic Testing (GWUT)
Appendix F to Part 192 I
Appendix F to Part 192 IIInspection Range
Appendix F to Part 192 IIIComplete Pipe Inspection
Appendix F to Part 192 IVSensitivity
Appendix F to Part 192 VWave Frequency
Appendix F to Part 192 VI
Appendix F to Part 192 VII
Appendix F to Part 192 VIIIDead Zone
Appendix F to Part 192 IXNear Field Effects
Appendix F to Part 192 XCoating Type
Appendix F to Part 192 XIEnd Seal
Appendix F to Part 192 XIIWeld Calibration to set DAC Curve
Appendix F to Part 192 XIIIValidation of Operator Training
Appendix F to Part 192 XIII.A
Appendix F to Part 192 XIII.B
Appendix F to Part 192 XIII.C
Appendix F to Part 192 XIV
Appendix F to Part 192 XV
Appendix F to Part 192 XVICalibration Onsite
Appendix F to Part 192 XVII
Appendix F to Part 192 XVIII
Appendix F to Part 192 XIX
Appendix G to Part 192Guidance on Moderate Consequence Areas
Appendix G to Part 192 I
Appendix G to Part 192 I.A
Appendix G to Part 192 I.B
Appendix G to Part 192 I.C

Plain-English summaries

49 CFR Part 192

Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards

Part 192 establishes minimum federal safety standards for the transportation of natural and other gas by pipeline. It applies to pipeline operators and covers materials, design, construction, welding and joining, corrosion control, testing, operations, maintenance, personnel qualification, and integrity management for both gas transmission and distribution pipelines.

§ 192.1(a)

This part sets minimum safety requirements for pipeline facilities and gas transportation, including pipelines on the outer continental shelf as defined in 43 U.S.C. 1331.

§ 192.1(b)(1)

Part 192 does not apply to offshore gathering lines in state waters that are upstream of the outlet flange of the production facility or the first facility where produced hydrocarbons are separated, dehydrated, or otherwise processed, whichever is farther downstream.

§ 192.1(b)(2)

Part 192 does not apply to producer-operated pipelines on the Outer Continental Shelf that cross into state waters without first connecting to a transporting operator's facility on the OCS, upstream (generally seaward) of the last valve on the last production facility on the OCS. Safety equipment protecting PHMSA-regulated pipeline segments is not excluded from Part 192. Producing operators for those upstream pipeline segments may petition the Administrator (or designee) for approval to operate under PHMSA regulations governing pipeline design, construction, operation, and maintenance under 49 CFR 190.9.

§ 192.1(b)(5)(ii)

This exclusion applies to a pipeline system that delivers only petroleum gas or petroleum gas/air mixtures to one customer and is entirely on that customer's property – even if part of the system runs through a public area – and such systems are not covered by Part 192.

Read the full text of 49 CFR Part 192

Subscribers get the full text, linked cross-references, and plain-English summaries as they pass the automated check against source text — $10 / month or $100 / year.

Subscribe Open the full reader